MOUNTING METHODS
Pre-curved vault panels can be installed using the following Decoustics ceiling systems:
1. Span (upward accessible, with 1/8” defined, closed reveal or open reveal panel joints).
2. Direct Mount (progressively accessible, with defined, closed reveal or open reveal panel joints).
3. Direct To Suspended Frame/Grid (progressively accessible with defined, closed reveal or open reveal panel joints).
4. Suspended Reveal (non-accessible, with open reveal panel joints).
5. Suspended Reveal (progressively accessible, with closed reveal panel joints).
6. Suspended Reveal ( upward accessible, with open reveal panel joints).
7. Ceilencio Custom (downward accessible, with defined panel joints).
8. Lay-In (upward accessible, with exposed suspension grid).
Note: Field cutting of panels is possible but not recommended.

RELATED DATA
Refer to specific ceiling system literature, e.g. Direct Mount, etc. for detailed data such as acoustical test data, ceiling system details including perimeter trim options (ensure trim is compatible with pre-curved panels), and similar information.

Note: The information provided in this Data Sheet is accurate to the best of our knowledge at the time of printing. However, we reserve the right to make changes when necessary without further notification. Suggested applications may need to be modified to conform with local building codes and conditions. We cannot accept responsibility for products that are not used, or installed, to our specifications.

Note: Only handle panels wearing clean, lightweight, white gloves during installation. Follow manufacturer's printed instructions for installation as well as field cutting of panels.
...
FINISH EDGE OPTIONS SIZES
CONSTRUCTION
THICKNESS
NRC
 WEIGHT COLOR

Fabric or
Vinyl
Resin: square edge; open or closed reveal joint.

Aluminum: square edge with 1/8” (3 mm) defined joint.
Fabric: Up to 48" x 120" (1220 mm x 3050 mm).

Vinyl: Up to 48" x 120" (1220 mm x 3050 mm).

Finish width must be sufficient to cover panel, panel thickness, and wrap minimum 1" (25 mm) on back side.
Panel consists of a 6 to 7 pcf (96 to 112 kg/m3) core. Fabric corners are fully tailored (no exposed darting). Vinyl corners are heat sealed. A 1 mil clear vapor retarder is adhered to panel back.
1"
(25 mm)


1 1/2"
(38 mm)

2"
(50 mm)		 0.85



0.95



1.05		 0.90 psf
(4.40 kg/m2)


1.20 psf
(5.90 kg/m2)

1.52 psf
(7.50 kg/m2)

As per selected finish

Claro
Aluminum: Claro coated square edge with 1/8” (3mm) defined joint.
Up to 72" x 48" (1830 mm x 1220 mm).



Handling larger panels may result in damage to finish. Consult Decoustics.
Panel consists of a 6 to 7 pcf (96 to 112 kg/m3) core with a 1/16" (1.5 mm) thick 16 to 20 pcf (256 to 320 kg/m3) high density integral facer designed to receive a non-bridging acoustically transparent Claro coating. A 1 mil clear vapor retarder is adhered to panel back.
1 1/16"
(27 mm)


1 9/16"
(40 mm)


2 1/16"
(52 mm)
0.80




N/A


N/A

............

 1.05 psf
(5.15 kg/m2)


1.40 psf
(6.84 kg/m2)


1.78 psf
(8.70 kg/m2)
Standard White CSW-100 Light Reflectance 92%

Custom colors mixed to match color chips

Quadrillo
Unfinished square kerf and spline, 3/32" (2.4 mm) edge banding veneer and solid wood face frame. Custom edge profiling on request.
48" x 60" (1220 mm x 1525 mm).
Panel consists of a 6 to 7 pcf (96 to 112 kg/m3) density mat faced core laminated between a layer of 1/4" (6 mm) thick Quadrillo face and a 1/8" (3 mm) HDF perforated backing board (QPP). Internal fire treated particle board framing as required for edge conditions.
Overall nominal thickness:
QPP-19
1- 1/8"
(28 mm)


QPP-25
1-3/8"
(35 mm)


QPP-50
2-3/8"
(60 mm)


0.80



0.90




1.00




2.80 psf
(13.68 kg/m2)

3.40 psf
(16.61 kg/m2)

5.5 psf
(26.85 kg/m2)
Anigre
Ash
Beech
Cherry
Mahogany
Maple
Oak
Paint Finish
Pear
Walnut


Custom on Request